18/10/2026 · GlucyView

Dexcom G7: signal loss, causes and solutions

Dexcom G7: signal loss, causes and solutions

Is your Dexcom G7 showing "Signal loss"? The message is common, especially at night, and in most cases the explanation is simple: the phone and the sensor can no longer talk to each other. Here is what happens, the most common causes and the checks to carry out, in order, based on Dexcom's official FAQs.

What happens during a signal loss?

The Dexcom G7 sensor sends a reading via Bluetooth every 5 minutes to your "display device" (the phone with the Dexcom G7 app, or the receiver). When these transmissions stop arriving, the app keeps the last value for a little over 10 minutes, then shows dashes, then the "Signal loss" message.

Important: during a signal loss, you receive neither readings nor alerts. Dexcom recommends using your blood glucose meter for any treatment decision during this time. The good news: when the signal comes back, up to 24 hours of missed readings can be filled back into the trend graph.

The most common causes

1. The phone is too far from the sensor

Dexcom advises keeping the display device within 6 metres of the sensor, with no obstacles. A wall, a closed door or water (bath, swimming pool) between the two is enough to break the connection. This is typical at night, when the phone is charging in another room.

2. The body blocks the signal

Bluetooth does not travel well through the body. Sleeping on the sensor, or keeping the phone in a back pocket (the body is then between the two), can cause a signal loss. In a child who moves a lot in their sleep, this is a common cause.

3. The Dexcom G7 app was closed

The app can run in the background, but if you close it completely (by "swiping" it away from the list of open apps), it no longer receives readings. Always leave it open, at least in the background.

4. The phone's battery and settings

This is often where it all comes down to. According to Dexcom:

  • Power saving mode can turn off Bluetooth and cause a signal loss. Keep the phone charged.
  • On Android, battery saver, adaptive battery and optimised charging can stop the app from running in the background, or close it while charging.
  • Focus or Paused app modes (Android) and the Downtime and App Limits features of Screen Time (iPhone) can block readings and alerts.
  • Bluetooth must stay on at all times.

Dexcom publishes a page of recommended settings for iPhone and for Android. Compare them with your phone's settings: menu names vary depending on the brand and version.

5. A phone or version that is not compatible

After an iOS or Android update, or with a new phone, the app may work less well if the combination has not yet been validated by Dexcom. Check the official list before updating: everything is explained in our article which phone is compatible with FreeStyle Libre 3 and Dexcom G7.

What to do, step by step

  1. Bring the phone closer to the sensor (less than 6 metres, no obstacles). Near water, bring it even closer.
  2. Check that the Dexcom G7 app is open, that the phone is charged and that it is not in power saving mode.
  3. Wait: a new reading can take up to 5 minutes to arrive, since the sensor only sends one reading every 5 minutes. In or near water, Dexcom says to wait up to 30 minutes.
  4. Turn Bluetooth off and on again, and wait 10 minutes.
  5. Restart the phone, then open the app again.
  6. Compare your settings with the settings Dexcom recommends for your phone.

Throughout, if you need to make a treatment decision, use your blood glucose meter and follow the plan agreed with your care team.

What if you use a Dexcom G6 or ONE+?

The principle is the same (Bluetooth link between the sensor and the phone), and the causes are often similar: distance, obstacles, app closed, battery settings. But timings and screens can differ from one system to another. For your model, consult the user manual and official Dexcom France support.

What loved ones see during a signal loss

Loved ones following with Dexcom Follow receive the data via the wearer's phone and the internet. If the phone no longer receives anything from the sensor, it has nothing to share: the follower no longer sees any new value. If Follow stays empty while the wearer can see their glucose, the problem is more likely with sharing: see our guide Dexcom Follow not working and the page Dexcom Share and LibreLinkUp troubleshooting.

The same goes for a display connected to sharing, such as GlucyView: it displays what Dexcom Share transmits, nothing more. During a signal loss, it does not receive any new value either. To find out how to enable sharing, see enable Dexcom Share step by step.

When should you contact Dexcom support?

Dexcom advises contacting its technical support if the signal loss alert lasts more than 30 minutes after carrying out these checks. Also contact them if signal losses happen often, or if the values seem inconsistent. In France, use the Dexcom contact page (online form or callback request). If you have symptoms, do not stay without a reading: do a fingerstick blood glucose test and apply the course of action agreed with your care team.

Frequently asked questions

Dexcom G6 signal loss: what should I do?

The first steps are the same as with the G7: bring the phone closer, check that the app is open and that Bluetooth is on, turn off power saving, then wait for the next reading. If the problem continues, refer to the G6 manual and Dexcom support.

Why does my Dexcom G7 lose signal at night?

Most often: the phone charging far from the bed or in another room, a child sleeping on their sensor, or the optimised charging setting (Android) closing the app while charging. Keep the phone near the bed and check the settings recommended by Dexcom.

How long does a signal loss last?

It lasts as long as the cause has not been fixed. Once the problem is solved, a new reading usually arrives within 5 minutes. If the alert lasts more than 30 minutes after your checks, contact Dexcom support.

Is data lost during a signal loss?

Not necessarily: according to Dexcom, up to 24 hours of missed readings can appear in the graph when the signal comes back. However, no alerts are sent during the interruption.

Why does my FreeStyle Libre 2 lose signal?

The causes are similar: phone too far away, Bluetooth off, app asleep. Read our article FreeStyle Libre "Alarms unavailable", which details the settings to check.

Dexcom, Dexcom Share and Dexcom Follow are trademarks of their owner. GlucyView is not affiliated with Dexcom. This article is for information only: if in doubt about your system, refer to Dexcom's official manual and support.

GlucyView is a display accessory for informational purposes only and is not a medical device. It never replaces your official CGM reader or receiver. Do not make any treatment decision based on it alone.

← Back to the journal